MY SERVICES
Custom industrial automation solutions, from design to commissioning
I turn your production needs into efficient, reliable systems ready for the future.
From concept to the technical implementation of products, systems and plants.
Design of electronic hardware, wireless systems and instrumentation.
- Electrical schematic design for analog and digital circuits
- PCB layout (routing) for single-layer, multi-layer and flexible boards
- Generation of manufacturing files (Gerber, Pick & Place, BOM)
- Design for Manufacturing (DFM) and Design for Test (DFT)
- Component selection and component obsolescence management
- Firmware development for 8/16/32-bit microcontrollers (PIC, AVR, ARM Cortex-M, ESP, Renesas, NXP, etc.)
- Development on embedded microprocessors with embedded Linux
- Bare-metal and RTOS-based programming (FreeRTOS, Zephyr, ThreadX)
- Driver development for hardware peripherals (UART, SPI, I2C, CAN, USB, Ethernet)
- Custom bootloaders and Over-The-Air (OTA) firmware updates
- Operational amplifiers (amplification, filtering, comparators)
- Signal conditioning for resistive sensors (strain gauges, RTDs, thermistors)
- Signal conditioning for active sensors (accelerometers, gyroscopes, MEMS pressure sensors)
- High-resolution ADC conversion (16/24-bit) for precision measurements
- DAC conversion for signal generation and analog control
- Active filters (low-pass, high-pass, band-pass, notch)
- Regulated linear power supplies
- Switching power supplies (Buck, Boost, Flyback, Forward, Half-Bridge, Full-Bridge)
- Isolated and non-isolated DC/DC converters
- Single-phase and three-phase inverters
- High-power LED drivers (constant current, PWM/analog dimming)
- Drivers for DC, Brushless (BLDC) and Stepper motors
- Battery management systems (BMS) for Li-Ion/LiFePO4 packs
- Intelligent battery chargers (CC/CV profiles, cell balancing)
- RF circuits: LNAs, mixers, power amplifiers
- Impedance matching and matching networks
- Antenna design and simulation (dipole, patch, Yagi, log-periodic, helical, parabolic)
- RF filters (low-pass, band-pass, resonant cavities)
- Splitters, combiners, circulators and duplexers
- Custom radio transmitter and receiver systems (HF, VHF, UHF, SHF)
- IoT systems with short-range wireless connectivity (Wi-Fi, Bluetooth/BLE, ZigBee, Thread, Matter)
- IoT systems with long-range LPWAN connectivity (LoRa/LoRaWAN, Sigfox, NB-IoT, LTE-M, 5G RedCap)
- Point-to-point and point-to-multipoint radio links (licensed and unlicensed)
- Link budget calculation and radio coverage
- Indoor GSM/LTE/5G cellular signal repeater systems
- Telemetry and remote control via radio or cellular network
- Industrial multiprotocol gateways and modems
- Custom datalogger design for data acquisition
- Automatic test systems (ATE - Automatic Test Equipment)
- Test benches for mass electronic production
- Integration of all kinds of sensors: temperature, pressure, humidity, gas, light, motion, proximity, force, acceleration, position
- Custom sensor design (capacitive, inductive, optical) for special applications
Software development, network architectures and server systems.
- Windows applications in C#/.NET, Python, C++, Java
- Software for data acquisition from instruments (serial, USB, Ethernet, GPIB interfaces)
- Supervisory and monitoring software for electronic systems and plants
- Configuration, diagnostics and calibration tools for embedded devices
- Desktop automation (Python scripts, PowerShell, VBA macros)
- Web frontend (HTML, CSS, JavaScript, React, Vue.js, Angular)
- Backend and REST/GraphQL APIs (Node.js, Python Flask/Django, .NET Core, Go)
- Web-based dashboards and control panels for remote monitoring
- Integration with cloud IoT platforms (AWS IoT, Azure IoT Hub, Google Cloud IoT, ThingsBoard)
- SaaS platforms for device fleet management
- Progressive Web Apps (PWA) and hybrid mobile applications
- Relational databases (MySQL, PostgreSQL, SQL Server, SQLite)
- NoSQL databases (MongoDB, Redis, Cassandra)
- Time-series databases for process data (InfluxDB, TimescaleDB, QuestDB)
- Data warehouses and Business Intelligence systems
- ETL (Extract, Transform, Load) for multi-source data integration
- Long-term data historization and compliant archiving
- Design of corporate LAN/WAN networks (structured cabling Cat.6/6A/7, optical fiber)
- Network segmentation with VLANs (Office / Production / Guest / IoT / DMZ separation)
- High-density Wi-Fi network design (site surveys, centralized controllers, fast roaming)
- Wireless mesh networks for large-area coverage (outdoor, warehouses, trade shows)
- Interconnection of remote sites (site-to-site VPN, MPLS, SD-WAN)
- Zero Trust network architectures
- Virtualized infrastructures (VMware vSphere, Proxmox VE, Microsoft Hyper-V, KVM)
- Application containerization (Docker, Kubernetes, Docker Compose, Podman)
- Centralized storage (NAS, SAN, RAID systems, Ceph, ZFS)
- Backup and disaster recovery systems (Veeam, Acronis, Borg, rsync)
- High availability and clustering (automatic failover, load balancing, heartbeat)
- Infrastructure as Code (Ansible, Terraform, Puppet)
- Secure network architectures (firewalls, UTM, IDS/IPS, WAF, proxies)
- Operating system hardening (Linux, Windows Server)
- Centralized authentication (LDAP, Active Directory, RADIUS, SSO, MFA)
- Corporate VPNs (OpenVPN, WireGuard, IPSec, SSL-VPN)
- IT/OT segmentation for industrial environments (IEC 62443)
- Digital certificate and PKI management
- Centralized logging and SIEM for event correlation
Automation of machines and plants, process instrumentation, robotics.
- PLC programming for any brand and platform
- Development in all IEC 61131-3 languages (Ladder, FBD, ST, IL, SFC)
- Custom Function Blocks and reusable libraries
- Program migration between different PLC platforms
- Production recipe management and multi-product parameterization
- Complex automatic sequences (batch, machine cycles, state management)
- Acquisition and scaling of analog signals (4-20mA, 0-10V, thermocouples, RTDs)
- High-speed counting for encoders and pulse sensors
- Integrated diagnostics and structured alarm management
- Data logging to local memory or external databases
- Soft-PLC on industrial PCs (Codesys, TwinCAT, WinAC)
- Offline simulation and debugging without physical hardware
- Electric motor sizing (Brushless, Induction, Stepper, Linear)
- Configuration and tuning of drives/inverters of any brand
- Control of single and synchronized multi-axis systems
- Electronic cams and complex motion profiles (S-curves, polynomial)
- Electronic gearing and virtual coupling
- Homing, zero-position search and encoder/resolver management
- Vector control and Field Oriented Control (FOC)
- Gantry systems, Cartesian portals and CNC kinematics
- Design of touch HMI interfaces of any brand
- SCADA systems for plant supervision (WinCC, Ignition, Movicon, Wonderware, AVEVA)
- Animated mimic diagrams for control rooms
- Multilevel alarm management with acknowledgment and history
- Graph trending and real-time data analysis
- Automatic production reports (PDF, Excel, scheduled emails)
- Integrated web server for remote browser access
- Integration and programming of robotic arms (Fanuc, ABB, Kuka, Yaskawa, Universal Robots, etc.)
- Collaborative robots (Cobots) for safe applications
- Design of robotic cells (pick & place, palletizing, bin picking, assembly)
- Design of gripping systems (pneumatic, electric, suction, magnetic grippers)
- Integration with machine vision for 2D/3D robot guidance
- Integration of smart industrial cameras (Cognex, Keyence, Basler, Omron, Sick)
- Surface defect inspection (scratches, dents, contamination)
- Vision-based dimensional inspection (geometric measurements, tolerances)
- Reading 1D/2D codes (barcodes, QR, Data Matrix, DPM)
- OCR/OCV character recognition
- Deep learning for complex defect classification
- Industrial lighting (backlight, dome, bar light, structured laser)
- Weighing: Load cells, weighing hoppers, belt weighers, gravimetric feeders
- Temperature: Thermocouples, RTDs, optical pyrometers, multi-zone PID temperature controllers
- Pressure/Flow/Level: Transducers, electromagnetic flow meters, ultrasonic, radar
- Position: Encoders, resolvers, optical scales, proximity sensors, LVDT
- Profibus DP/PA, Profinet RT/IRT networks
- Ethernet/IP, DeviceNet, Modbus RTU/TCP networks
- CANopen, CANbus J1939, AS-Interface networks
- CC-Link, IO-Link, EtherCAT, Powerlink networks
- Gateways, protocol converters and multi-network bridges
- Integration of industrial wireless sensors for condition monitoring
- IIoT gateways for collecting data from legacy machines (OPC-UA, MQTT, Sparkplug B)
- Edge computing for local data processing
- Integration with corporate MES and ERP platforms (SAP, Oracle, Zucchetti)
- Digital Twin and predictive models for maintenance
- Real-time production dashboards (OEE, KPI, machine downtime)
- Design of safety chains according to EN ISO 13849 and IEC 62061
- Calculation of Performance Level (PL) and Safety Integrity Level (SIL)
- Integration of safety relays and safety PLCs
- Optoelectronic barriers, laser scanners, safety mats
- Interlocks, emergency buttons, two-hand controls
- Verification and validation of safety systems
- Electrical schematics with CAD (Eplan, Spac Automazione, AutoCAD Electrical)
- Sizing of circuit breakers and residual current protection
- Sizing of power, signal and shielded cables
- Design of automation and distribution electrical panels
- UPS systems and generator sets with automatic switching
- Industrial power factor correction and power quality analysis
- Power metering and energy consumption monitoring
Technical interventions, troubleshooting, maintenance and operational support.
Repair, diagnostics and maintenance of electronic equipment and radio systems.
- Fault diagnosis on analog and digital electronic boards
- Repair with replacement of SMD and PTH components (including BGA with rework station)
- Repair of switching and linear power supplies
- Repair of power drivers for motors and LEDs
- Repair of inverters and DC/DC converters
- Repair of control boards and embedded CPUs
- Replacement of degraded electrolytic capacitors (recapping)
- Replacement of backup batteries and supercapacitors
- Firmware reprogramming on repaired devices
- Reconstruction of electrical schematics from boards without documentation
- Identification of unknown or custom components
- Cloning of discontinued boards for spare parts
- Analysis of recurring failures to identify original design defects
- Firmware recovery from microcontrollers (when not protected)
- Diagnosis of firmware malfunctions (freezes, resets, abnormal behavior)
- Debugging with JTAG/SWD probes and logic analyzers
- Memory integrity verification (Flash, EEPROM, FRAM)
- Communication protocol analysis with oscilloscope and bus analyzer
- Firmware bug fixing and patch release
- Tuning and alignment of RF filters and resonant cavities
- Verification and adjustment of transmission power
- Measurement and optimization of SWR (Standing Wave Ratio) on lines and antennas
- Replacement of RF connectors and damaged coaxial cables
- Diagnosis and repair of transceivers (PMR, VHF/UHF, amateur radio)
- Verification of receiver sensitivity and selectivity
- Electromagnetic interference (EMI) mitigation
- Diagnosis of connectivity issues (packet loss, disconnections, reduced range)
- Reconfiguration of LoRaWAN, Sigfox, NB-IoT gateways and nodes
- Remote and on-site firmware updates for IoT devices
- Replacement of failed radio modules (Wi-Fi, BLE, LoRa, LTE)
- Verification of radio coverage with portable instrumentation
- Calibration of multimeters, oscilloscopes, signal generators
- Calibration of dataloggers and data acquisition systems
- Verification of the measurement chain with reference samples
- Periodic certification of laboratory instruments
- Programming and initial setup of new instrumentation
Systems support, data recovery, security and IT infrastructure management.
- Diagnosis and repair of hardware faults (power supplies, motherboards, RAM, storage)
- Removal of viruses, malware, ransomware
- Performance optimization of slow systems
- Reinstallation and configuration of operating systems (Windows, Linux)
- Data migration between PCs and hardware upgrades
- Workstation configuration for technical use (CAD, development, simulation)
- Data recovery from damaged hard drives (mechanical and SSD)
- Data recovery from degraded or failed RAID arrays
- System recovery after a ransomware attack
- Disk cloning of critical systems before failure
- Implementation and verification of backup procedures
- Periodic recovery testing (restore tests)
- Diagnosis of connectivity issues (slowness, disconnections, packet loss)
- Traffic analysis with Wireshark and network monitoring tools
- Fault finding on copper and optical fiber cabling (OTDR/TDR reflectometry)
- Verification of switch, router and firewall configurations
- Resolution of IP conflicts and DHCP/DNS problems
- Throughput and latency optimization
- Removal of unauthorized access and backdoors
- Log analysis for intrusion detection
- Patching and updating vulnerable systems
- Firewall reconfiguration after a security incident
- Verification and correction of VPN policies
- MFA (Multi-Factor Authentication) implementation
- Troubleshooting virtual machines (VMware, Proxmox, Hyper-V)
- Recovery of corrupted or unbootable VMs
- Storage expansion and virtual disk management
- VM migration between hosts or datastores
- Troubleshooting Docker containers and orchestrators
- Proactive monitoring and alerting (Zabbix, Grafana, Prometheus)
- Diagnosis of connectivity issues with cloud services (latency, timeouts)
- Reconfiguration of API integrations after upstream changes
- Management of SSL/TLS certificate expirations
- Troubleshooting SSO and OAuth authentication
- Cloud cost optimization (instance right-sizing, orphan resource cleanup)
Interventions on machines, production lines, plants and industrial instrumentation.
- Urgent intervention on stopped machinery (combined electrical/software/mechanical diagnosis)
- PLC diagnostics analysis (error reading, I/O states, variable tracing)
- Fault diagnosis on drives and inverters (fault code reading, parameter verification)
- Fieldbus troubleshooting (Profibus, Profinet, Modbus, CANopen, EtherCAT)
- Verification of wiring and connections with multimeter and oscilloscope
- Identification of the causes of intermittent or sporadic stops
- Periodic backup of PLC, HMI, robot and CNC programs
- Verification and replacement of backup batteries on CPUs and drives
- Check of capacitor and fan condition on inverters and power supplies
- Cleaning and inspection of electrical panels (terminal tightening, thermal checks)
- Firmware updates for PLCs, drives and field devices
- Periodic verification of safety chains and safety devices
- Electronic modernization of machines with obsolete PLCs
- Replacement of discontinued drives with modern equivalents
- Migration from relay logic systems to PLCs
- HMI upgrade from button/lamp panels to touch screens
- Plant adaptation to new regulations (Machinery Directive, safety requirements)
- Industry 4.0 integration on legacy machines (IoT retrofit)
- Repair of inverters and drives (board analysis, replacement of IGBTs, drivers, capacitors)
- Repair of industrial switching power supplies
- Repair of axis control boards (encoder interface, DAC, I/O)
- Repair of analog and digital I/O boards
- Repair of HMI panels (touch replacement, backlight, power supply)
- PLC repair (CPU replacement, I/O modules, communication boards)
- Repair of servo drives and brushless motors (encoders, brake, windings)
- Weighing: Calibration of scales and load cells, tare reset, repeatability verification
- Temperature: Calibration of temperature controllers, thermocouple and PT100 offset verification, furnace profiling
- Pressure/Flow/Level: Transducer calibration, flow meter calibration, zero and span verification
- Position: Verification of encoder accuracy, alignment of optical scales, calibration of proximity sensors
- Physical diagnosis of fieldbuses (Profibus, CANbus) with oscilloscope
- Signal quality analysis and reflections on RS-485 lines
- Verification of terminations and shielding
- Resolution of collisions and CRC errors on industrial networks
- Diagnosis of issues on industrial Ethernet networks (Profinet, Ethernet/IP, EtherCAT)
- Verification of cycle times and determinism of real-time networks
- Setup of vibration monitoring systems on motors and gearboxes
- Thermographic analysis to identify hotspots on panels and motors
- Monitoring of absorbed currents to detect bearing or transmission degradation
- Configuration of alarm thresholds and trend analysis
- Integration of vibration/temperature data with SCADA/MES
- Configuration of industrial VPN routers (eWON, IXON, Tosibox, Secomea, HMS)
- Setup of secure remote access to PLCs, HMIs and robots
- Remote diagnosis and troubleshooting without an on-site visit
- Remote machine status monitoring and alarm notifications
- Diagnosis of robotic errors and faults (log analysis, verification of encoders, motors, brakes)
- Robot recovery after collision (axis recalibration, mastering)
- Trajectory optimization and cycle time reduction
- Software updates for robots and controllers
- Backup and restore of robot programs
- Diagnosis of recognition issues (lighting, focus, algorithms)
- Camera recalibration after movement or replacement
- Optimization of inspection parameters to reduce false rejects
- Cleaning and maintenance of optics and illuminators
- Vision software updates
Analysis, feasibility studies, expert opinions, certifications and strategic support.
Technical consulting, feasibility analysis and decision support in electronics and telecommunications.
- Feasibility assessment of new electronic products (concept, requirements analysis, technical risks)
- Trade-off analysis between different technological solutions (MCU vs FPGA, wired vs wireless, etc.)
- Development cost estimation and implementation timelines
- Identification of critical components and supply risk assessment
- Proof of Concept (PoC) and demonstration prototypes
- Review of third-party electrical schematics and PCB layouts (identification of errors, critical issues, improvements)
- Firmware code audit for quality, security and maintainability
- Analysis of the causes of recurring failures in products in production
- Second opinion on projects under development
- Make-or-buy evaluation of components/subsystems
- Support for CE marking of electronic equipment (EMC, RED, LVD Directives)
- EMC pre-compliance: analysis and mitigation of issues before accredited lab testing
- Support for international certifications (FCC, IC, UKCA, MIC Japan)
- Consulting on specific product regulations (IEC 60601 medical, EN 50155 railway, etc.)
- Preparation of technical documentation for the technical file
- Frequency planning and channelization for private radio networks
- Radio coverage and link budget calculation for wireless systems
- Interference analysis and electromagnetic compatibility between systems
- Support for frequency use authorization requests to the Ministry (MISE/MIMIT)
- Consulting on radio regulations and emission limits
- Technical expert reports on failures or malfunctions of electronic equipment
- Analysis of fire causes or damage attributable to electronic defects
- Expert reports for legal disputes and support as a party-appointed technical consultant (CTP)
- Damage assessment for insurance purposes
- Analysis of counterfeit or non-compliant products
- Technology scouting: identification of components, modules and solutions for specific needs
- Benchmarking between products and development platforms
- Evaluation and qualification of new electronics suppliers
- Technical due diligence for acquisitions or investments in hardware startups
- Audits of electronics manufacturing suppliers (EMS)
Strategic IT consulting, security audits, architecture assessment and decision support.
- Network infrastructure assessment (topology, segmentation, redundancy, critical issues)
- Verification of firewall, switch and router configuration
- Evaluation of backup and disaster recovery systems
- Audit of server and storage systems (capacity, performance, obsolescence)
- Gap analysis against industry best practices
- Vulnerability assessment on networks and systems
- Verification of security configuration and policies
- Attack surface exposure analysis (exposed services, open ports)
- Verification of credential management and privileged access
- Log analysis and detection of signs of compromise
- Report with risk classification and remediation roadmap
- Evaluation of on-premise vs cloud vs hybrid for new projects
- TCO (Total Cost of Ownership) analysis for different infrastructure options
- Reference architectures for high availability and disaster recovery
- Consulting on containerization and microservices
- Application modernization roadmap
- Drafting of technical specifications for tender documents (purchase of HW, SW, IT services)
- Support in evaluating technical proposals
- Verification of the technical and economic consistency of supplier quotes
- Work supervision for complex IT projects
- GDPR gap analysis for IT systems and procedures
- Support for implementing GDPR technical measures (encryption, pseudonymization, logging)
- Consulting on NIS2 regulations for critical infrastructures
- Preparation for ISO 27001 certifications
- Drafting of IT security policies and procedures
- Forensic acquisition of digital evidence (disks, logs, emails, smartphones)
- Malware analysis and reconstruction of attack timelines
- Technical expert reports for legal disputes in IT
- Support as a party-appointed technical consultant (CTP) in civil and criminal proceedings
- Assessment of economic damages from cyber incidents
Consulting for automation, machine safety, Industry 4.0, expert reports and support for industrial projects.
- Pre-engineering studies for new plants or production lines
- ROI analysis for the automation of manual processes
- Trade-off evaluation between different technological solutions (robots vs manipulators, PLCs vs industrial PCs, etc.)
- High-level layout and plant sizing
- Support in selecting machine builders and system integrators
- Risk analysis according to EN ISO 12100
- Evaluation of required and achieved Performance Level (PL)
- Compliance verification with Machinery Directive 2006/42/EC and the new Machinery Regulation 2023/1230
- Gap analysis of safety measures on existing machines
- Support in preparing the Technical File and Declaration of Conformity
- Safety audit on third-party machines (for used machine purchases or disputes)
- Digital assessment: evaluation of the company’s digital maturity
- Industry 4.0 roadmap: prioritization of actions to maximize ROI
- Consulting on the technical requirements of Industry 4.0 assets (interconnection, MES/ERP integration)
- Support for expert reports for tax incentives (Industry 4.0 tax credit, former Hyper/Super depreciation)
- Evaluation of IIoT and MES platforms (selection, PoC, implementation)
- Production line performance audit (OEE analysis, bottlenecks, cycle times)
- Energy consumption analysis and efficiency improvement proposals
- Optimization of format changeover times (SMED)
- Root Cause Analysis on quality problems or recurring downtime
- Benchmarking between plants or similar lines
- Expert reports on machine failures with attribution of responsibility (manufacturer, user, maintainer)
- Expert reports for contractual disputes (machines not compliant with specifications)
- Damage assessment for industrial losses
- Expert reports for workplace accidents (analysis of technical causes)
- Support as a party-appointed technical consultant (CTP) in arbitrations and disputes
- Drafting technical specifications and tender documents for machine purchase
- Support in evaluating manufacturers’ technical offers
- Participation in FAT (Factory Acceptance Test) at the manufacturer’s site
- Work supervision and installation oversight
- Management of SAT (Site Acceptance Test) and punch lists
- Verification of contractual KPI achievement (cycle time, quality, availability)
- PLC programming courses (basic, advanced, brand-specific)
- Training on fieldbuses and industrial networks
- Training on SCADA and HMI systems
- Training on machine safety and regulations
- Courses on embedded electronics and firmware
- On-the-job training on the client's specific plants
When conventional solutions are not enough, you invent.
Not every problem has an answer already available on the market. There are challenges for which a solution still does not exist: applications where conventional batteries are not enough, environments where standard electronics do not survive, production processes that no one has ever automated, technical needs that no off-the-shelf product can satisfy.
This is exactly where real engineering work begins: inventing what does not exist.
The Research & Development work I carry out is aimed at creating radically new solutions for applications where existing technologies fail, whether because of extreme operating conditions, non-standard requirements, or simply because no one has ever tackled that problem before.
But the objective goes beyond the single project. It is not just about solving the need of a specific client: it is about developing technologies that can benefit entire industrial sectors, filling gaps that the market does not cover today and creating products and systems that did not exist before, but that tomorrow could become the standard.
It is a different approach: not selling what already exists, but building what is still missing; turning an unsolved problem into an opportunity; seeing a limit not as an obstacle, but as the starting point for innovation.
If you have a need that no existing product satisfies, a problem that no one has solved yet, or an idea that no one has realized yet, let's talk about it. Impossible challenges are the ones worth taking on.
WHY CHOOSE ME
What sets me apart and why I could be the right partner for your project.
Multidisciplinary
Electronics, automation, IT and telecommunications: a single point of contact for complex projects that span multiple disciplines.
Responsive
Fast response, available even for urgent issues and unexpected situations. No endless waiting or bouncing between departments.
Pragmatic
Practical solutions that work, not style exercises. The goal is to solve the problem, on time and within the agreed budget.
Direct
You speak with the person working on your project, with no intermediaries, salespeople or project managers. Fast communication, quick decisions.
Hands-on
Years of field experience, not just theory. I know the real problems in plants and what it means to keep things running every day.
Innovative
When needed, I can invent new solutions. I don't stop at "it can't be done", I look for the way to make it happen.
FREQUENTLY ASKED QUESTIONS
Answers to the most common questions about how I work, costs, timelines and how we can collaborate.
You can contact me by email, phone or WhatsApp. Briefly tell me what you need: a problem to solve, a project to develop, an idea to evaluate. I usually reply within 24 hours and, if necessary, we schedule a call or meeting to discuss it in more detail.
Yes, the quote is always free and with no obligation. For simple projects, a phone call is enough. For complex projects, a site visit or preliminary analysis may be needed: in that case, I will let you know in advance if there are any costs.
It depends on the complexity of the project. A support intervention may take a few hours or days. A complete design project may take weeks or months. In the quote I always indicate the estimated timelines, and I stick to them.
Both. I carry out many activities remotely (design, software development, consulting). For installations, commissioning, troubleshooting and work on plants, I come on-site. I am available for travel throughout Italy and abroad.
I am based in Italy, but I regularly work with clients throughout Europe. For remote activities there are no geographical limits. For on-site work, I evaluate each case based on duration and logistics.
I remain available for corrections and post-delivery support. If it is my mistake, I fix it at no additional cost. If new needs or changes emerge, we evaluate them together. The goal is for the project to work, not to close the ticket as quickly as possible.
Yes, I work with companies of every size, startups, and also private clients with interesting projects. I do not have minimum amounts: if the project makes sense and I can be useful, let's talk.
Certainly. I work exclusively with formal invoicing. For Italian companies, I issue electronic invoices through SDI. For foreign clients, invoices comply with EU regulations.
Yes, for projects that require specific expertise or particular qualifications (such as filings, sworn statements, and certifications), I collaborate with a network of qualified professionals. This allows me to guarantee full compliance with current regulations at every stage.
Absolutely. I offer focused consulting to help you understand what you need, assess feasibility, get a second opinion, or orient yourself on technology choices. There is absolutely no obligation to continue with me.
WHAT PEOPLE SAY ABOUT ME
Private Messages
← Swipe to view →
Public Reviews
READY TO INNOVATE?
Do you have a project in mind or a technical problem to solve? Let's talk about it. I turn your needs into practical and efficient solutions.